Cylindricity in GD&T: Definition and Measurement
Cylindricity in GD&T explained: definition and symbol, how it differs from roundness and concentricity, and how to measure it with a CMM for shafts, seals, and bearing journals.
Cylindricity in GD&T: Definition, Measurement and Applications
Cylindricity in geometric dimensioning and tolerancing (GD&T, ASME Y14.5) is a form tolerance that controls how far a cylindrical feature may deviate from a perfect cylinder. It combines roundness, straightness, and parallelism along the entire axis into a single tolerance zone. For turned parts, shafts, bearing seats, and seal surfaces, cylindricity is often the tolerance that decides fit and function.
In this guide we explain the definition and symbol, show the difference from roundness and concentricity, walk through measurement with a CMM and roundness tester, and give practical design recommendations.
What is Cylindricity?
The cylindricity tolerance defines a three-dimensional tolerance zone bounded by two coaxial cylinders spaced a radial distance t apart. Every point of the actual surface must lie within this zone. Unlike roundness, which checks a single cross-section, cylindricity evaluates the entire surface along its length — so it also catches conical or barrel-shaped deviations.
The symbol is the letter **⌭** (a circle flanked by two slanted lines) in a feature control frame. Crucially, cylindricity is a form tolerance with no datum; the value applies to the whole cylindrical surface and must be met regardless of the actual diameter.
Cylindricity vs Roundness vs Concentricity
These three tolerances are often confused but answer different questions. **Roundness** (circularity) checks one cross-section in a plane — a wavy but perfectly round shape on every plane passes roundness. **Cylindricity** adds axial straightness and parallelism: two cross-sections where one is larger (cone or barrel) violate the tolerance. **Concentricity** is a location tolerance that references the axis to a datum, not a form feature.
Practically: for a short, rigid part with tight bearing support, roundness may be enough. For long shafts, seal seats, and bearing journals — where any form error along the length causes leaks, wear, or vibration — cylindricity is the more robust specification.
How to Measure Cylindricity
Cylindricity is a three-dimensional quantity and cannot be reliably checked with simple hand tools like calipers. Standard methods are:
**Coordinate measuring machine (CMM):** The CMM probes several cross-sections along the axis (typically 4–8 trace circles distributed over the length) and fits the best reference cylinder. The software computes the minimum radial envelope zone enclosing all measured points — its width is the measured cylindricity.
**Roundness / form tester:** A precision rotary table with a high-resolution probe (e.g. an inductive styli) spins the workpiece while the probe travels across multiple height positions. This delivers the highest resolution for hardened or high-precision parts (turned spindles, bearings, hydraulic components) and also captures micro-waviness.
**Tolerance zone principle:** Regardless of method, a minimum-envelope cylinder zone is fitted over all captured points; the radial difference between the inner and outer cylinder is the measured value. Compare it against the tolerance value in the frame — if smaller, the part is conforming.
When to Use Cylindricity
Use cylindricity when function depends on the geometry of the whole cylindrical surface — not just a single cross-section:
**Rotating shafts and spindles:** Any cone or barrel form causes unbalance, vibration, and higher bearing loads. Cylindricity limits the shaft form over its full length, protecting runout and service life.
**Seal seats (O-ring, radial lip seal):** An out-of-round or conical sealing surface causes leaks and premature wear. The tolerance secures an even contact band across the full sealing line.
**Bearing journals and bushing seats:** For press fits and bearings, controlled form over the full length is critical for even load distribution. This prevents local overload and seating damage.
Design Best Practices
Apply cylindricity only to genuinely function-critical features — it is expensive to manufacture (often extra CMM inspection time) and drives cost when unnecessarily tight. As with all form tolerances, start with a practical value and loosen it whenever assembly allows.
Combine cylindricity with an appropriate size and surface-finish tolerance. Because it checks the whole surface, a finer roughness value makes sense where O-rings or sealing lips seat. Also make sure the inspection method (CMM vs form tester) matches the required resolution — very tight tolerances below roughly 5 µm demand a form tester, not just a CMM.
### FAQ
**What is the difference between cylindricity and roundness?** Roundness checks only one cross-section; cylindricity evaluates the entire cylindrical surface along its length and also includes straightness and parallelism.
**Does cylindricity require a datum?** No. Cylindricity is a form tolerance without a datum; it limits the whole surface independent of diameter and axis location.
**How is cylindricity measured?** With a coordinate measuring machine (CMM) probing multiple cross-sections along the axis, or with a high-resolution roundness/form tester. In both cases a minimum-envelope cylinder zone is fitted over all measured points.
**What if I do not specify cylindricity?** Form is only indirectly controlled by size and runout parameters. On long shafts without a cylindricity tolerance, a cone or barrel form can go unmonitored and cause vibration or leaks.
Conclusion
Cylindricity is the form tolerance that ensures a perfect cylindrical surface across the entire length — essential for shafts, seal seats, and bearing journals. It is not the same as roundness and requires three-dimensional measurement with a CMM or form tester. At metalbizz.com our engineers inspect parts with CMM and help you apply the right GD&T for turned and stamped parts — [see our inspection services →](/inspection) and [request a quote →](/en/rfq).